Sundstrand 15 Series, Hydrostatic Transmissions, Repair Parocedures Manual 1974

September 30, 2016, 1:40 pm

≫ Next: Sundstrand 18 Series, Hydrostatic Transmissions, Service Manual 1974

≪ Previous: Summit Level II Bandit, Programming Manual Year (1979)

$

0

0

http://industrialmanuals.com/sundstrand-series-hydrostatic-transmissions-repair-parocedures-manual-1974-p-5198.php

Sundstrand 15 Series, Hydrostatic Transmissions, Repair Procedures Manual Year (1974)

 
This Manual Covers Models:
Hydrostatic
This Manual Includes:
The purpose of this manual is to provide the procedures for the repair of the Sundstarnd Major Repair 15 Series Family of Hydrostatic Transmissions. These Instructions cover the inline and U Type Transmissions in addition to the fixed displacement motors and variable displacement pumps. Major repairs are those requiring the removal of the end cap or center section and include complete disassembly of the Unit.

Inline Transmission:
Major Repairs
General Parts Information

U Type Transmission
Fixed Displacement Motor
Variable Displacement Pump

This Manual Has 50 Printed Pages.
Year 1974

---

Sundstrand 18 Series, Hydrostatic Transmissions, Service Manual 1974

October 3, 2016, 6:45 am

≫ Next: Sundstrand BT505484 Omnimill OM2, w-Control System Mechanical Maintenance Manual

≪ Previous: Sundstrand 15 Series, Hydrostatic Transmissions, Repair Parocedures Manual 1974

$

0

0

http://industrialmanuals.com/sundstrand-series-hydrostatic-transmissions-service-manual-1974-p-5199.php

Sundstrand 18 Series, Hydrostatic Transmissions, Service Manual Year (1974)

 
This Manual Covers Models:
18 Series
This Manual Includes:
Configuration and Specifications
System Circuit Description
Fluid Recommendations
Start Up Procedure
System Maintenance
Trouble shooting Procedures
Minor Repair Procedures
Major Repair Procedures
General Parts Identification
Fixed Displacement Motor
Variable Displacement Pump and Motor

This Manual Has 56 Printed Pages.
Year 1974

Sundstrand BT505484 Omnimill OM2, w-Control System Mechanical Maintenance Manual

October 3, 2016, 6:46 am

≫ Next: Sundstrand BT50584 Omnimill OM2 w/ 4 Axis Contouring Control Operators Manual

≪ Previous: Sundstrand 18 Series, Hydrostatic Transmissions, Service Manual 1974

$

0

0

http://industrialmanuals.com/sundstrand-bt505484-omnimill-wcontrol-system-mechanical-maintenance-manual-p-1813.php

Sundstrand BT505484 Omnimill OM2 w/ 4 Axis Contouring Control System Mechanical Maintenance Manual Year (1965)        

This Manual Covers Models:
BT505484
OM2
Omnimill

This Manual Includes:
This Manual has been prepared as an aid to the Mechanical Maintenance Personnel who bear the responsibility
of Investigating and ultimately repairing mechanical Malfunctions that May Occur during Operation of the Machine

Chapter 1: Machine Description and Outline
Chapter 2: Machine Base Unit
Chapter 3: Table Rotation Feed Drive Unit
Chapter 4: y Axis Saddle, Feed Drive and Counterbalance
Chapter 5: Head Saddle
Chapter 6: OM2 Low Speed Spindle Head
Chapter 7: Automatic Tool Changer
Chapter 8: Pallet Indexer Unit
Chapter 9: Lubrication
Chapter 10: Miscellaneous Information
Table of Contents in Photographs Provided
This Manual Has 253 Printed Pages.
Year 1965

Sundstrand BT50584 Omnimill OM2 w/ 4 Axis Contouring Control Operators Manual

October 3, 2016, 6:48 am

≫ Next: Sundstrand MCE 101A, Mobile Load Controller Manual 1985

≪ Previous: Sundstrand BT505484 Omnimill OM2, w-Control System Mechanical Maintenance Manual

$

0

0

http://industrialmanuals.com/sundstrand-bt50584-omnimill-axis-contouring-control-operators-manual-p-1812.php

Sundstrand BT50584 Omnimill OM2 w/ 4 Axis Contouring Control System Operators Manual Year (1965)        

This Manual Covers Models:
BT505484
OM2
Omnimill

This Manual Includes:
Table of Contents
List of Illustrations
Section 1: Machine Familiarization
Section 2: Machine Motions & Capabilities
Section 3: Machine Specifications
Section 4: Tape Format
Section 5: Bendix Machine Control Unit (MCU)
Section 6: RhEEM Tape Reader
Section 7: Operators Control Console
Position Indicator Panel
Operators Control Pallet Changer
Manual Tool Change Control
Section 8: Operating Procedures
Section 9: Programming Procedures
Section 10: Programming Example
Section 11: Tooling Concepts
Section 12: Operators Duties & Preventive Maintenance Prcedures
Appendix

List Of Illustrations: Illustrations Correspond to the first 11 Sections
This Manual Has 152 Printed Pages.
Year 1965

Sundstrand MCE 101A, Mobile Load Controller Manual 1985

October 3, 2016, 6:50 am

≫ Next: Sundstrand MCV104A, Electreical Displacement Control Manual 1983

≪ Previous: Sundstrand BT50584 Omnimill OM2 w/ 4 Axis Contouring Control Operators Manual

$

0

0

http://industrialmanuals.com/sundstrand-101a-mobile-load-controller-manual-1985-p-5201.php

Sundstrand MCE 101A, Mobile Load Controller Manual Year (1985)

 
This Manual Covers Models:
MCE
101A
This Manual Includes:
Specifications
Instructions
Theory of Operation
Wiring Schematic
Troubleshooting
Adjustments

This Manual Has 8 Printed Pages.
Year 1985

Sundstrand MCV104A, Electreical Displacement Control Manual 1983

October 3, 2016, 6:52 am

≫ Next: Sundstrand Model 10, Lathe, Installation - Operation - Maintenance Manual

≪ Previous: Sundstrand MCE 101A, Mobile Load Controller Manual 1985

$

0

0

http://industrialmanuals.com/sundstrand-mcv104a-electreical-displacement-control-manual-1983-p-5202.php

Sundstrand MCV 104A, Electrical Displacement Control Manual Year (1983)

 
This Manual Covers Models:
MCV 104A
This Manual Includes:
Specifications
theory of Operation
Schematic of the Internal Working of the MCV104A
Wiring
Installation
Mounting
Mounting the New Hardware
Pump Neutral Adjustment
Ordering Information
Connectors

This Manual Has 8 Printed Pages.
Year April 1983
Bulletin 95-8965-2

Sundstrand Model 10, Lathe, Installation - Operation - Maintenance Manual

October 3, 2016, 6:54 am

≫ Next: Gold Machine

≪ Previous: Sundstrand MCV104A, Electreical Displacement Control Manual 1983

$

0

0

http://industrialmanuals.com/sundstrand-model-lathe-installation-operation-maintenance-manual-p-2351.php

Sundstrand Model 10, Automatic Lathe, Installation – Operation – Maintenance Manual           

This Manual Covers Models:
Model 10
This Manual Includes: 
Nomenclature
Installation
Chip Pans
Coolant System
Electric Controls
Starting of Machine
Setting up Machine
Service Information
Lubrication Chart
Unit Assembly Drawings & Instructions:
Drive to Main Drive Shaft
Spindle Assembly
Feed Box Units
Feed Drive Unit
Front Carriage with Angular Feed in and Tool Relief (Standard)
Front Carriage with Straight Feed in Attachment (extra)
Front Carriage Dwell Attachment (extra)
Rear Carriage
Tailstock
Auxiliary Overhead Slide (extra)
Standard Tooling (extra)
Typical Tooling Applications

This Manual Has  34 Printed Pages.
1^st Edition

Gold Machine

October 4, 2016, 9:48 am

≫ Next: Sundstrand Model 12, Automatic Lathe, Parts & Assembly Drawings Manual Year 1941

≪ Previous: Sundstrand Model 10, Lathe, Installation - Operation - Maintenance Manual

$

0

0

The Gold of the world is a machine that keeps on growing.

Roughly one0fifthe of the world's stock of gold-worth over $200 Billion USD is stored under the streets of london.
About 6500 tons of gold are stored in seven vaults under the streets.The largest vault belongs to the Bank of England, and accounts for about 76% of the total stash. Most of this underground gold is in the form of standard bars weighing 400 troy ounces. The total value has been assessed as representing one-fifth of the world's entire supply of gold, worth more than $248 Billion USD (172 billion).

I hope the USA keeps buying.

---

Sundstrand Model 12, Automatic Lathe, Parts & Assembly Drawings Manual Year 1941

October 4, 2016, 9:51 am

≫ Next: Sundstrand Model 4A, 6A 8A 12A 16A, Automatic Lathes, Operations Manual

≪ Previous: Gold Machine

$

0

0

http://industrialmanuals.com/sundstrand-model-automatic-lathe-parts-assembly-drawings-manual-year-1941-p-2328.php

Sundstrand Model 12, Automatic Lathe, Parts & Assembly Drawings Manual Year (1941)        

This Manual Covers Models:
No. 12
12

This Manual Includes: 
Parts List
Repair Parts
Functional Illustrated Diagrams Showing Component Identification
This Manual Has  16 Printed Pages.
Year 1941

Sundstrand Model 4A, 6A 8A 12A 16A, Automatic Lathes, Operations Manual

October 4, 2016, 9:54 am

≫ Next: Sundstrand Model 55 Rigidmil, Milling Machine, Assembly Drawings Manual 1948

≪ Previous: Sundstrand Model 12, Automatic Lathe, Parts & Assembly Drawings Manual Year 1941

$

0

0

http://industrialmanuals.com/sundstrand-model-automatic-lathes-operations-manual-p-2350.php

Sundstrand Model 4A, 6A, 8A, 12A, 16A, Automatic Lathes, Operations Manual          

This Manual Covers Models:
Model 4A
6A
8A
12A
16A

This Manual Includes: 
Nomenclature
Installation
Lubrication Chart
Coolant System
Electric Controls
Spindle Clutch and Brake, Rapid Motor Brake
Starting of Machine
Setting up Machine
Service Information
Spindle Assembly
Feed Box Units
Front Carriage with Angular Feed in, Dwell and Tool Relief (Standard)
Front Carriage with Straight Feed In Attachment (extra)
Rear Carriage
Feed In and tool Relief For Rear Slide
Auxiliary overhead Slide (extra)
Tailstock
This Manual Has  31 Printed Pages.

Sundstrand Model 55 Rigidmil, Milling Machine, Assembly Drawings Manual 1948

October 4, 2016, 9:57 am

≫ Next: Sundstrand Model 6A, Automatic Lathe, Parts and Assembly Drawings Manual 1954

≪ Previous: Sundstrand Model 4A, 6A 8A 12A 16A, Automatic Lathes, Operations Manual

$

0

0

http://industrialmanuals.com/sundstrand-model-rigidmil-milling-machine-assembly-drawings-manual-1948-p-2336.php

Sundstrand Model 55 Rigidmil, Milling Machine, Assembly Drawings Manual Year (1948)         

This Manual Covers Models:
Model 55
Rigidmil

This Manual Includes: 
Table Cycles
Master Control switch
Electrical Controls
Lubrication Piping Diagram
Lubricator Unit
Coolant Pump & Piping (Simplex)
Coolant Pump & Piping (Duplex)
Overarm & Braces
Feed Box
Table Drive, Anti-Backlash Nut & Positive Stop
Spindle Head (25hp)
Spindle Head (50hp)
Spindle Brake
This Manual will be copied from a Xerox
It is Very Good and Intellectually Sound
The Drawings are from 1948-1951

This Manual Has  20 Printed Pages.
Year March 1948

Sundstrand Model 6A, Automatic Lathe, Parts and Assembly Drawings Manual 1954

October 4, 2016, 9:58 am

≫ Next: Sundstrand Model 8, Automatic Lathe, Install - Operations & Assembly Manual

≪ Previous: Sundstrand Model 55 Rigidmil, Milling Machine, Assembly Drawings Manual 1948

$

0

0

http://industrialmanuals.com/sundstrand-model-automatic-lathe-parts-assembly-drawings-manual-1954-p-2342.php

Sundstrand Model 6A, Automatic Lathe, Parts List and Assembly Drawings Manual Year (1954)         

This Manual Covers Models:
Model 6A
This Manual Includes: 
Parts Lists
Functional Illustrated Diagrams Showing Component Identification
Machine Photo's
This Manual Has  22 Printed Pages.
Year February 1954

Sundstrand Model 8, Automatic Lathe, Install - Operations & Assembly Manual

October 5, 2016, 6:11 am

≫ Next: Sundstrand Model 8, Automatic Lathe, Parts List & Assembly Drawings Manual 1941

≪ Previous: Sundstrand Model 6A, Automatic Lathe, Parts and Assembly Drawings Manual 1954

$

0

0

http://industrialmanuals.com/sundstrand-model-automatic-lathe-install-operations-assembly-manual-p-2348.php

undstrand Model 8, Automatic Lathe, Installation – Operation – Maintenance  & Assembly Manual          

This Manual Covers Models:
Model 8

This Manual Includes: 
Nomenclature
Installation
Chip Pans
Coolant System
Electric Controls
Starting Machine
Setting Up Machine
Service Information
Lubrication
Unit Assembly Drawings & Instructions:
Drive to Main Drive Shaft
Spindle Assembly
Feed Box Units
Feed Drive Unit
Front Carriage with angular Feed-In and Tool relief (Standard)
Front Carriage With Straight Feed-In Attachment (extra)
Front Carriage Dwell Attachment (extra)
Rear Carriage
Tailstock
Auxiliary Overhead Slide (extra)
Standard Tooling (extra)
Typical Tooling Applications
Form #8-2
Edition 4
This Manual Has  33 Printed Pages.

Sundstrand Model 8, Automatic Lathe, Parts List & Assembly Drawings Manual 1941

October 5, 2016, 6:14 am

≫ Next: Sundstrand Model 8A, Automatic Lathe, Parts and Assembly Drawings Manual 1950

≪ Previous: Sundstrand Model 8, Automatic Lathe, Install - Operations & Assembly Manual

$

0

0

http://industrialmanuals.com/sundstrand-model-automatic-lathe-parts-list-assembly-drawings-manual-1941-p-2349.php

Sundstrand Model 8, Automatic Lathe, Parts List & Assembly Drawings Manual Year (1941)          

This Manual Covers Models:
Model 8

This Manual Includes: 
Parts Lists
Assembly Drawings
Functional Illustrated Diagrams Showing Component Identifications
This Manual Has  19 Printed Pages.
Year March 1941

Sundstrand Model 8A, Automatic Lathe, Parts and Assembly Drawings Manual 1950

October 5, 2016, 6:16 am

≫ Next: Sundstrand Model OM4 & 5 Omnimil Attachments Parts and Assembly Drawings Manual

≪ Previous: Sundstrand Model 8, Automatic Lathe, Parts List & Assembly Drawings Manual 1941

$

0

0

http://industrialmanuals.com/sundstrand-model-automatic-lathe-parts-assembly-drawings-manual-1950-p-2341.php

Sundstrand Model 8A, Automatic Lathe, Parts List and Assembly Drawings Manual Year (1950)         

This Manual Covers Models:
Model 8A
This Manual Includes: 
Parts Lists
Functional Illustrated Diagrams Showing Component Identification
Machine Photo's
This Manual Has  24 Printed Pages.
Year August 1950

---

Sundstrand Model OM4 & 5 Omnimil Attachments Parts and Assembly Drawings Manual

October 5, 2016, 6:18 am

≫ Next: Sundstrand Model OM4 Omnimil, Milling, Parts and Assembly Drawings Manual 1958

≪ Previous: Sundstrand Model 8A, Automatic Lathe, Parts and Assembly Drawings Manual 1950

$

0

0

http://industrialmanuals.com/sundstrand-model-omnimil-attachments-parts-assembly-drawings-manual-p-2339.php

Sundstrand Model OM4 OM5 Omnimil, Milling Machine, Parts List and Assembly Drawings of Attachments Manual Year (1958         

This Manual Covers Models:
OM4
OM5
Omnimil

This Manual Includes: 
Parts Lists
Functional Illustrated Diagrams Showing Component Identification
Way Guards & Chip Guards

This Manual Has 10 Printed Pages.
Year October/November 1957

Sundstrand Model OM4 Omnimil, Milling, Parts and Assembly Drawings Manual 1958

October 5, 2016, 6:21 am

≫ Next: Sundstrand Rigidmil, Milling Machines, Parts Lists & Assembly Drawings Manual

≪ Previous: Sundstrand Model OM4 & 5 Omnimil Attachments Parts and Assembly Drawings Manual

$

0

0

http://industrialmanuals.com/sundstrand-model-omnimil-milling-parts-assembly-drawings-manual-1958-p-2338.php

Sundstrand Model OM4 Omnimil, Milling Machine, Parts List and Assembly Drawings Manual Year (1958)         

This Manual Covers Models:
OM4
Omnimil

This Manual Includes: 
Parts Lists
Functional Illustrated Diagrams Showing Component Identification
Photo's and Plate Drawings

This Manual Has  34 Printed Pages.
Year June 1958 and Drawings before1958

Sundstrand Rigidmil, Milling Machines, Parts Lists & Assembly Drawings Manual

October 6, 2016, 11:22 am

≫ Next: Sundstrand Transmission Pumps Motors & Controls, 20-27 Series Manual 1980

≪ Previous: Sundstrand Model OM4 Omnimil, Milling, Parts and Assembly Drawings Manual 1958

$

0

0

http://industrialmanuals.com/sundstrand-rigidmil-milling-machines-parts-lists-assembly-drawings-manual-p-2353.php

Sundstrand Rigidmil, Milling Machine, Parts List & Assembly Drawings Manual (1940-1950)            

This Manual Covers Models:
No. 0
No. 00
No. 1
No. 33 Fluid-Screw
No. 8 Automatic Lathe
No. 10 Automatic Lathe
No. 12 Automatic Lathe
8 Inch Stub Lathe


Rigidmil
This Manual Includes: 
Functional Illustrated Drawings Showing Component Identification
How to Order Repair Parts (3^rd Edition with Diagrams)
Unit Assembly Drawings for Rockford Rigidmil's

This Manual Has  136 Printed Pages.
Year 1940-1950's

Sundstrand Transmission Pumps Motors & Controls, 20-27 Series Manual 1980

October 6, 2016, 11:24 am

≫ Next: Sundstrand Transmission Repair Procedures Manual 1981

≪ Previous: Sundstrand Rigidmil, Milling Machines, Parts Lists & Assembly Drawings Manual

$

0

0

Sundstrand Transmission Pumps Motors & Controls, 20-27 Series Manual Year (1980)

 
This Manual Covers Models:
20-27 Series
This Manual Includes:
Configuration:
Pumps
Motors
Controls
Maintenance
Basic Operation: Hydrostatic Transmission
Basic Operation: Hydraulic Support System
Variable Pump-Fixed Motor Flow SCHEMATIC
Trouble shooting
Control Adjustments
Minor REPAIRS
General Parts Identification
Metric Conversion Chart

This Manual Has 42 Printed Pages.
Year 1980

Sundstrand Transmission Repair Procedures Manual 1981

October 6, 2016, 11:28 am

≫ Next: Sunhill Shengshing SDM-15, 15" Wide Belt Sander, Owner Manual Year (1997)

≪ Previous: Sundstrand Transmission Pumps Motors & Controls, 20-27 Series Manual 1980

$

0

0

http://industrialmanuals.com/sundstrand-transmission-repair-procedures-manual-1981-p-5197.php

Sundstrand Transmission Repair Procedures Manual Year (1981)

 
This Manual Covers Models:
Hydrostatic
This Manual Includes:
The purpose of this manual is to provide the procedures for the repair of the Sundstarnd Heavy Duty family of Hydrostatic Transmissions. These instructions are provided for both the fixed displacement motors and the variable displacement pumps and are divide into Minor and Major Repairs.

General Parts Lists
Functionally Illustrated Drawings showing Component Identification

This Manual Has 50 Printed Pages.
Year January 1981
Revision B